Your Plumbing Crash Course: A Guide to Installing a Bathtub

Book Your Service

What are your ideas concerning A Step-by-Step Guide to Installing a Bathtub?


Tools You Need to Install a New Bathtub
Setting up a tub isn't precisely rocket science, yet it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub and also position the new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also embeded in the new one. Make sure you have actually certified yourself for the job and also are comfortable attempting it. Instead of working with a specialist to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Possibilities are you might need a professional plumber to make tube connections.
This article will aid you set up a new bathtub in your restroom if you have currently gotten a new tub and also do not need to change the setup of your previous supply of water pipelines.
Your devices as well as material list ought to comprise the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Planning for the Installation


    To start with, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to stop pressure on the bath tub.
    Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you utilize every one of the provided washing machines.
    Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must now prepare to be suited its last position.

    Removing Old Taps


    If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be quite problematic due to the limited access that is frequently the case.
    Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will originate from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
    Prior to moving on to fit the new taps, compare the pipeline connections on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

    Setting up the Bathtub


    Making use of the two wooden boards under its feet, place the bathtub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
    The next goal is to ensure that the tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bathtub up until the spirit level reads degree.
    To set up taps, fit the bottom of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
    Turn on the water supply and also inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
    Lastly, take care of the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the tub has actually been made use of at least once as this will settle it right into its last position.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
    If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next, position the tap in the placing opening in the bath/basin making sure that the washing machines are in location in between the faucet and also the sink. Protect the tap in place with the producer provided backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind must be attached to the tap finishes first, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the area where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, causing issues with dampness and possible leakages to the ceiling listed below.
    You can pick from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water before sealing, to permit the motion experienced when the tub is in usage. The sealant can fracture relatively very early if you do not take into consideration this motion prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water-proof glue and grout.

    How to Install a Freestanding Bathtub?


    Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.



    This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.


    Slope


    Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.


    Placement


    A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.



    According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.


    Clean the bathroom floor


    After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.


    Steps to Install a Freestanding Bathtub:


    STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.



    STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.



    STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.



    STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.



    STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.



    STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.


    Tips to Maintain a Freestanding Bathtub:


  • Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


  • Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


  • Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


  • Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


  • Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


  • If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

  • https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps


    Tools You Need to Install a New Bathtub

    I'm certainly very excited about How to Install a Bathtub Yourself and I hope you liked the new blog entry. Be sure to set aside a second to share this article if you enjoyed reading it. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Book An Estimate Now

    Leave a Reply

    Your email address will not be published. Required fields are marked *